Share this: Facebook Twitter Reddit LinkedIn WhatsApp DESIGN AND DEVELOPMENT OF SMALL SCALE AUTOMATED BLDC MOTOR SPEED CONTROL SYSTEM Abstract The speed control of a permanent magnet brushless DC motor (PMBLDC) is very important because it can indirectly control the required mechanical performance and efficiency. The control of this parameter has been demonstrated in several documents using various controllers […]
Design of a SET Based 4-bit ALU Using Proteus
Table of Contents List of Figures List of Tables Abstract 1.0 Introduction 2.0 Design Methodology 2.1Design of a 3-bit ALU using Proteus: A case study 2.2Basic components 2.2.1 Adder/Subtractor Block 2.2.2 Array Multiplier 2.2.3 Multiplexers 2.3 Design of a 4-bit ALU using Proteus 2.3.1 Operation table for a 4-bit ALU 2.3.2Adder/Subtractor block 2.3.3 4-Bit Comparator […]
Development of Material and Manufacturing Process for Exhaust Manifold
Share this: Facebook Twitter Reddit LinkedIn WhatsApp Development of Material and Manufacturing Process for Exhaust Manifold Abstract Exhaust Manifold is an integral part of the Exhaust System designed to collect exhaust gases from the cylinder and channel them to the exhaust outlet. This paper deals with the alternative material and manufacturing process to replace the convention material and manufacturing technique […]
Double Piezoelectric Micropump
Abstract This paper discusses the development of a new micropump based on microfabrication techniques that can be used for drug delivery. First, actuation methods are examined to define the working principle and the advantages/disadvantages of each actuation method, such as electrostatic, thermal, piezoelectric and magnetic. Next, examples of micropumps that employ these actuation methods […]
Effects of Gain Constants Proportional Integral (PI) Control Experiment
Share this: Facebook Twitter Reddit LinkedIn WhatsApp Abstract: The usage and effects of gain constants proportional integral (PI) control were explored throughout this experiment. The experiment adjusted the proportional and integral constants to perform five different tests. The group tested using only proportional feedback, only integral feedback, both proportional and integral feedback with no set point parameter, traditional PI control […]
Electrification of Ford Focus Using Lithium-ion Battery
Abstract – The main objective of this report is to achieve the full electrification of the ford focus sedan. Along with that the study of the battery packs placing in the ford focus sedan to enhance the vehicle performance in terms of the range, economy. To make the battery system works properly and to get most of […]
Extent to Which Radio-frequency Identification Self-service Technology Improves and Hinders Library Customer Service
Reference this Share this: Facebook Twitter Reddit LinkedIn WhatsApp Extent to which radio-frequency identification self-service technology improves and hinders library customer service Radio-frequency identification (RFID) self-service technology has both enhanced and impeded the delivery of customer service in libraries. According to Li, Deng, and Bertino (2014), RFID is a form of technology which allows for automatic recognition and tracking of […]
Failure Analysis of Adhesively Bonded Joints
Failure Analysis of Adhesively Bonded Joints Table of Contents List of Figures 1 Introduction 2 Literature review 2.1 Analytical approach for adhesively bonded joints 2.1.1 Elastic analysis 2.1.1.1 Volkersen model 2.1.1.2 Goland and Reissner model 2.1.2 Non-linear adhesive analysis 2.1.2.1 Hart-Smith model 2.1.2.2 Bigwood and Crocombe model 2.1.2.3 Adams and Mallick 2.1.3 Non-linear adhesive and adherend analysis 2.1.3.1 Wang et al. model 2.1.3.2 Adams et al. model 2.2 Failure […]
Failure of Metals under Long Term Static Loads
Failure of metals under long term static loads Introduction Metals are an important factor in almost every aspect of contemporary life, as such it is essential that designers have sufficient knowledge of the behaviour of these materials when subjected to different types of loads in a variety of environments (Gere and Goodno 2012). In practical […]
Product Design of a Fran Blade
1. Manufacturing Concepts 1.1 Product Design Specification of fan blade To effectively develop a Product Design Specification for the Fan Blade, we need to firstly define the basic functions of the Fan blade. The basic function of a fan is to cause effective air flow in a room and this should be accomplished for a […]